- 您现在的位置：买卖IC网 > Sheet目录983 > HMC6343-EVAL (Honeywell Microelectronics & Precision Sensors)EVAL BOARD FOR HMC6343
HMC6343
Operational Mode Registers
EEPROM registers 0x04 and 0x05 contain bits that are read for operational mode status and for setting the Run Mode
measurement rate. The tables below describe the register contents and interpretation. It is recommended that Operational
Mode Register 1 and 2 written only to change default orientation and update measurement rate.
Table 4 – Operational Mode Register 1 (EEPROM 0x04)
OM1_7
Comp(0)
OM1_6
Cal(0)
OM1_5
Filter(0)
OM1_4
Run(1)
OM1_3
Stdby(0)
OM1_2
UF(0)
OM1_1
UE(0)
OM1_0
Level(1)
Table 5 – Operational Mode Register 1 Bit Designations
Location
OM1_7
OM1_6
OM1_5
OM1_4
OM1_3
OM1_2
OM1_1
OM1_0
Name
Comp
Cal
Filter
Run
Stdby
UF
UE
Level
Description
Calculating compass data if set. (read only)
Calculating calibration offsets if set. (read only)
IIR Heading Filter used if set.
Run Mode if set.
Standby Mode if set.
Upright Front Orientation if set.
Upright Edge Orientation if set.
Level Orientation if set
Table 6 – Operational Mode Register 2 (EEPROM 0x05)
OM2_7
(0)
OM2_6
(0)
OM2_5
(0)
OM2_4
(0)
OM2_3
(0)
OM2_2
(0)
OM2_1
MR1(0)
OM2_0
MR0(1)
Table 7 – Operational Mode Register 2 Bit Designations
Location
OM2_7 to
OM2_2
OM2_1 to
OM2_0
Name
0
MR1, MR0
Description
These bits must be cleared for correct operation.
Measurement Rate
0,0 = 1Hz
0,1 = 5Hz (default)
1,0 = 10Hz
1,1 = Not Assigned
User Hard-Iron Calibration
The HMC6343 provides a user calibration routine with the 0x71 command permitting entry into the calibration mode and
the 0x7E command to exit the calibration mode.
After entering the calibration mode, rotate the device reasonably steady for 360 degrees about the Y (Left - Right) axis
and then 360 degrees about Z (Up - Down) axis. During the first rotation, maintain the Y axis at Level as much as
possible. Maintain the Z axis upright as much as possible during the second rotation and until the exit calibration
12
www.honeywell.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
HMR2300-D21-232-DEMO
KIT DEVELOP MAGNETOMETER RS232
HMR3000-DEMO-232
KIT DEMO DIG COMPASS MODUL RS232
HMU-PATBH101KQ-3M
CABLE ASSEMBLY MU FIBER OPTIC 3M
HP-BRACKET
ACCY BRACKET FOR HP RELAYS
HP100SS
HOLE PLUG 1" STAINLESS STEEL
HP100
HOLE PLUG 1" STEEL
HP125SS
HOLE PLUG 1.25" STAINLESS STEEL
HP125
HOLE PLUG 1.25" STEEL
相关代理商/技术参数
HMC634LC4
制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:ACTIVE BIAS CONTROLLER
HMC634LC4_09
制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC DRIVER AMPLIFIER, 5 - 20 GHz
HMC634LC4TR
制造商:Hittite Microwave Corp 功能描述:IC MMIC DVR AMP GAAS 24SMD
HMC634-SX
功能描述:IC MMIC POWER AMP DIE 制造商:analog devices inc. 系列:- 包装:托盘 零件状态:在售 频率:5GHz ~ 20GHz P1dB:23dBm 增益:22dB 噪声系数:7dB RF 类型:通用 电压 - 电源:5V 电流 - 电源:180mA 测试频率:- 封装/外壳:模具 供应商器件封装:模具 标准包装:2
HMC635
制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC DRIVER AMPLIFIER, 18 - 40 GHz
HMC635_09
制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC DRIVER AMPLIFIER, 18 - 40 GHz
HMC6352
制造商:Honeywell SSEC 功能描述:Magnetoresistive Sensor 2-Axis 24-Pin LCC 制造商:Honeywell Sensing and Control 功能描述:COMPASS-ON-A-CHIP 2AXIS 制造商:Honeywell Microelectronics And Precision Sensors 功能描述:MAGNETIC SENSOR; Magnetic Field Min:0.10G; Magnetic Field Max:0.75G; MSL:MSL 3 - 168 hours; Sensor Terminals:SMD; Supply Current:10mA; Supply Voltage:5.2V; Terminal Type:PCB 制造商:Honeywell 功能描述:Magnetoresistive Sensor 2-Axis 24-Pin LCC
HMC6352-DEMO
功能描述:DEMONSTRATION BOARD FOR HMC6352 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035